Manual mode

 

M01:We would like to check the set temperature (ramp and delay).

M02:We want to set a delay of 120 minutes (without starting the program).

M03:We want to reach a temperature of 900°C.

M04:We want to constantly regulate the temperature of 1100°C and turn it off ourselves after a certain time.

M05:We need to reach a temperature of 1000°C at a rate of 4°C/min and hold the temperature for 1 hour.

M06:We want to execute the same program as last time.

M07:Tomorrow (Thursday) at 4:00 p.m. we want to start the already set manual program.

M08:On Tuesday morning at 8:30, we want to regulate to 600°C and maintain this temperature until the program is stopped manually.

M09:A program has been started by mistake and we want to close it immediately.

M10:We want to reduce the temperature rise rate in the already running program to 3.5°C per minute

M11:In the already running program, we want to change the set temperature to 700 °C.

M12:We need to extend the delay by 20 minutes in an already running program.

M13:We would like to pause a running program and resume it after a certain period of time.

M14:We want to skip the currently executed ramp in the running manual program.

 

Menu

 

M15:We would like to look at the latest events in the controller.

M16:We would like to look at the penultimate course and display its graph.

M17:We want to find out what was the power consumption of the last run.

M18:We would like to find out which firmware version the controller is using.

M19:We want to find out what IP address the controller uses (it must be connected to the network).

M20:We need to look at the manual and enlarge the desired page (PRO version only).

M21:We want to find out what was the power consumption of the last run.

M22:We want to find out what the currently set ramp (rate of temperature change) is.

M23:We want to look at the set parameters of the manual mode.

M24:We need to find out how long the program has been running.

 

Programming mode

 

P01:We would like to select and run program 3.

P02:We need to label program 3 with our own label.

P03:We request to display the graph of program number 3.

P04:We need to copy program number 3 into program number 5.

P05:We need to delete program number 3.

P06:We want to see program number 5.

P07:We need to create a new program number 3 (now free). We would like to enter a delay of 120 minutes at a temperature of 1000°C, which we will reach as quickly as possible.

P08:In an hour we would like to start program number 3.

P09:For program number 3, we would like to change the delay to 60 minutes.

P10:Program number 8 is very long, block number 99 can no longer be overwritten.

P11:We request to run program number 8 only from the fifth block.

P12:We need to program the temperature course given by the graph. We will use the free program 1.

P13:We require the most accurate start-up with a ramp of 1°C/min to a temperature of 150°C (we will limit the power consumption of the device to 15%). We will use the free program number 4.

P14:We want to maintain a temperature of 1180°C every day from 6:00 a.m. to 6:00 p.m., and 400°C at night. We require the controller to reach temperature in one hour in the morning. We will use the free program 2.

P15:We need to program the cycle specified by the graph. The cycle will be carried out daily from six o'clock in the morning, after the end of the cycle the maintenance temperature will be 200°C. We will use program number 9.

P16:We need to 1100°C at a rate of 5°C/min and then a continuous delay. During the temperature increase, the damper on the digital output O4 must be opened. We will use the free program 7.