Example M01

We would like to check the set temperature (ramp and delay).

1. With a button  (Start) we get to the launch preparation screen

2. We check the set temperature in the left part of the screen

3. We return to the home screen with the button  (Back)

Example M02

We want to set a delay of 120 minutes (without starting the program).

1. With a button  (Start) we get to the launch preparation screen

2. With the button  (Delay) we go to enter a manual delay

3. Enter the value120using numbers or arrows

4. Confirm the value with the button

5. We return to the home screen with the button  (Back)

Example M03

We want to reach a temperature of 900°C.

1. With a button  (Start) we get to the launch preparation screen

2. With the button  (Temperature) we go to the temperature setting

3. Enter the value 900 using numbers or arrows

4. Confirm the value with the button

5. Start the regulation with the button  (Start)

Example M04

We want to constantly regulate the temperature of 1100°C and turn it off ourselves after a certain time.

1. With a button  (Start) we get to the launch preparation screen

2. With the button  (Temperature) we go to the temperature setting

3. Enter the value 1100 using numbers or arrows

4. Confirm the value with the button

5. With the button  (Delay) we go to enter a manual delay

6. Enter the value0using numbers or arrows

7. Confirm the value with the button  In the case of a delay, an inscription appears instead of the time Cont

8. Start the regulation with the button  (Start)

9. Now the regulation is in progress, which we interrupt after a certain time with the button  (Stop)
10. On the program stop screen, confirm the stop again with the button  (Stop)

11. This exits the manual program and displays the home screen

Example M05

We need to reach a temperature of 1000°C at a rate of 4°C/min and hold the temperature for 1 hour.

1. With a button  (Start) we get to the launch preparation screen

2. With the button  (Temperature) we go to the temperature setting

3. Enter the value 1000 using numbers or arrows

4. Confirm the value with the button

5. With the button  (Ramp) we go to enter a manual delay

6. Enter the value 4 using numbers or arrows

7. Confirm the value with the button

8. With the button  (Delay) we go to enter a manual delay

9. Enter the value 60 using numbers or arrows (input is in minutes)

10. Confirm the value with the button

11. Start the regulation with the button  (Start)

Example M06

We want to execute the same program as last time.

1. With a button  (Start) we get to the launch preparation screen

2. Since we do not need to change any parameters, we confirm the launch with the button  (Start)

Example M07

Tomorrow (Thursday) at 4:00 p.m. we want to start the already set manual program.

1. With a button  (Start) we get to the launch preparation screen

2. The parameters are pre-set, we go to setting the delayed start time with the button  (Later)

3. Press the button Ct for the program to run on Thursday

4. We press the buttons one by one  1   6   0   0  which will set the start time to 4:00 p.m

5. Confirm the delayed start by pressing the button  (Later)

Example M08

On Tuesday morning at 8:30, we want to regulate to 600°C and maintain this temperature until the program is stopped manually.

1. With a button  (Start) we get to the launch preparation screen

2. With the button  (Temperature) we go to the temperature setting

3. Enter the value 600 using numbers or arrows

4. Confirm the value with the button

5. With the button  (Delay) we go to enter a manual delay

6. Enter the value0using numbers or arrows

7. Confirm the value with the button  In the case of a delay, an inscription appears instead of the time Cont

8. The parameters are now set, we move on to setting the delayed start time with the button  (Later)

9. Press the button  Tu  for the program to run on Tuesday

10. We press the buttons one by one  0   8   3   0  which sets the start time to 8:30 in the morning

11. Confirm the delayed start by pressing the button  (Later)

Example M09

A program has been started by mistake and we want to close it immediately.

1. Press the button on the home screen  (Stop)
2. On the screen for stopping the program, confirm the stop again with the button  (Stop)

Example M10

We want to reduce the temperature rise rate in the already running program to 3.5°C per minute

1. Press the button on the home screen  (Stop)

2. With the button  (Ramp) we move on to entering the newly required speed of temperature rise

3. Enter the value 3.5 using numbers (and decimal point) or arrows

4. Confirm the value with the button

5. We return to the home screen with the button  (Back)

Example M11

In the already running program, we want to change the set temperature to 700 °C.

1. Press the button on the home screen  (Stop)

2. With the button  (Temperature) we go to change the set temperature

3. Enter the value 700 using numbers or arrows

4. Confirm the value with the button

5. We return to the home screen with the button  (Back)

Example M12

We need to extend the delay by 20 minutes in an already running program.

1. Press the button on the home screen  (Stop)

2. With the button  (Delay) we move on to entering the delay time at the set temperatures

3. Use numbers or arrows to enter a value 20 minutes longer than what is currently displayed

4. Confirm the value with the button

5. We return to the home screen with the button  (Back)

Example M13

We would like to pause a running program and resume it after a certain period of time.

1. Press the button on the home screen  (Stop)

2. Pause the program with the button  (Pause), the status bar turns red

3. We return to the home screen with the button  (Back)

4. After a certain time on the home screen, we press the button  (Stop)

5. Start the program again with the button  (Pause), status bar green

6. We return to the home screen with the button  (Back)

Example M14

We want to skip the currently executed ramp in the running manual program.

1. Press the button on the home screen  (Stop)

2. Press the button  (Skip), a confirmation button will appear next to it for 5 seconds

3. Confirm skipping the block with the button  (OK), the ramp will be skipped and the delay will begin

4. We return to the home screen with the button  (Back)